How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
Blog Article
We have found this post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the internet and concluded it made good sense to discuss it with you over here.
Mounting a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily accessible, the project can relocate speedily; if you need to open a wall to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will require a helper to leave the old tub and set in the brand-new one. See to it you have actually qualified yourself for the job and fit trying it. Instead of employing a professional to take over a halfway-completed project, it is far better to take into consideration utilizing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This short article will certainly assist you set up a new bath tub in your shower room if you have already acquired a brand-new tub and do not require to change the arrangement of your previous supply of water pipes.
Your devices as well as material list must comprise the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel all set for the staying water that will originate from the pipes. When the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in place between the faucet and also the sink. Secure the tap in position with the supplier offered backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former type ought to be connected to the tap ends first, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Utilizing the two wood boards under its feet, position the bathtub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four small points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level and also changing the feet on the tub up until the spirit level reads level.
To mount faucets, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water system as well as check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has been used at the very least once as this will certainly settle it into its last placement.
Getting ready for the Installment
Firstly, the supporting structure supplied with the bath needs to be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to break an inflexible seal, causing the water to permeate the wall surface between the bath as well as the tiling, bring about problems with moisture and also possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to permit the activity experienced when the tub is in use. The sealer can split rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that editorial on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from an acquaintance on a different web address. Are you aware of another individual who is interested by the topic? Feel free to promote it. We value reading our article about Tools You Need to Install a New Bathtub .
Click Here!
Report this page